SiegelSeal N07+

High Performance Industrial Silicone

$8.14 each $4,884.00 / Pallet
SKU: SSN07G600x12-50

SELECT VOLUME: Pallet

SELECT COLOUR: Grey

Suitable For

  • Automotive
  • HVAC
  • Sheet Metal
  • Roofing
  • Guttering
  • Waterproofing
25 Year Warranty
Low VOC
Industrial Silicone
SiegelSeal N07+ is high-performance neutral oxime cure 100% silicone sealant. This high performance formulation is engineered for a wide range of industrial applications. These include sealing lap and structural joints in applications such as automotive, HVAC, sheet-metal, roofing, guttering and waterproofing applications where lifetime high strength sealing performance is required. This silicone conforms with Australian Steel Institute Technical Specification TS-001 as being neutral cure 100% silicone and approved and warranted for roofing and guttering applications.
Sealant Type Neutral Oxime Cure Silicone
Colour Colours &  Translucent
Density 1.00 ± 0.03 g/ml ASTM D792
Sheen Full Sheen
SiegelSeal N07+ is high-performance neutral oxime cure 100% silicone sealant. This high performance formulation is engineered for a wide range of industrial applications. These include sealing lap and structural joints in applications such as automotive, HVAC, sheet-metal, roofing, guttering and waterproofing applications where lifetime high strength sealing performance is required. This silicone conforms with Australian Steel Institute Technical Specification TS-001 as being neutral cure 100% silicone and approved and warranted for roofing and guttering applications.
  • High Adhesion
  • Easy Tooling and Finishing
  • Maximum UV Resistance
  • Extreme Temperature Resistance
  • Very Low Odour
  • Non-corrosive
  • Non-yellowing

SiegelSeal N07+ is engineered to ensure lifelong performance in demanding applications such as automotive, HVAC, sheetmetal, roofing, guttering and waterproofing applications.

Instructions: Remove a sausage of SiegelSeal N07+ from the carton and place in the sausage gun. Holding the sausage gun upright, use side cutter or a knife to cute the metal crimp off one end of the sausage. Cut a nozzle down to the desired nozzle diameter and place in the nozzle clasp and screw on the end of the gun. Ensure the surface is correctly prepared or primed. Pump the silicone as required. SiegelSeal N07+ must be tooled with light pressure within 5 minutes post-application to spread the material against the joint surface for a professional finish. For but joints, SiegelSeal N07+ should be applied to a joint of at least 5x5mm, and bigger joints have a width to depth ratio of about 2:1. SiegelSeal N07+ in its uncured state can be cleaned with solvent. When cured it is very difficult to remove.

Certified & Approved

  • Greenstar Low VOC Compliant
  • AS4020:2018 certified for Potable Water and food contact
Sealant Type Neutral Oxime Cure Silicone
Colour Translucent & Colours
Density 1.00 ± 0.03 g/ml ASTM D792
Sheen Full Sheen
Shore Hardness A 30 ASTM D2240
Tensile Strength 1.5 N/mm² ASTM D412
Application Temperature +5°c to +50°c
Temperature Resistance -60°c to +180°c
Smoke Point 220°c +/-
Low VOC Compliance Yes GBCA Greenstar Compliant
VOC Content 39 grams / litre ASTM D3960-05
Curing Speed 3mm / 24 hours (23°c and 50% R.H)
Movement Capacity 25% ± ASTM C719
Elongation at Break ≥400% ASTM D412
Sagging 0mm ISO 7389
Skin Formation 5 -10 minutes (23°c and 50% R.H)
0 Reviews

What Our Customers Are Saying

5
0
4
0
3
0
2
0
1
0
REVIEWS (0)
Write a Review
Add a review

Your email address will not be published. Required fields are marked *

Your rating *

  • Australian Owned
  • Technical Support
  • Fast Dispatch
  • Bulk Supply Available
  • Commercial Grade Tested

Related Products

Need help selecting the right product?

Access Technical Data Sheets, Safety Data Sheets and expert recommendations from our technical team.

Anything else to discuss?

Access Technical Data Sheets, Safety Data Sheets and expert recommendations from our technical team.

Speak to Technical Team